制砂机系列Sand Maker

当前位置:首页>>产品中心>>制砂机系列Sand Maker

GPR立式冲击破碎机(Sand Maker)

作者: admin 时间:2021-05-17 06:11:17 来源:
摘要:GPR立式冲击式破碎机是从结构到工作原理都不同于常规颚式破碎机、圆锥破碎机和辊式破碎机等强制式破碎设备,也不同于常规球磨机和自磨、半自磨机等概率式粉磨设...
GPR立式冲击破碎机(Sand Maker)

GPR立式冲击式破碎机是从结构到工作原理都不同于常规颚式破碎机、圆锥破碎机和辊式破碎机等强制式破碎设备,也不同于常规球磨机和自磨、半自磨机等概率式粉磨设备,又不同于传统反击式破碎机和锤式破碎机等冲击式破碎设备的一种新型冲击式破碎机。GPR立式冲击式破碎机广泛用于金属和非金属矿石、水泥、耐火材料、铝矾土、金刚砂、玻璃原料、建筑材料、人工造砂以及各种冶金矿渣的细碎,特别对中硬、特硬物料比其他类型的破碎机更具有优越性。
 
GPR立式冲击式破碎机特点:
(1) 结构简单合理、运行成本低。利用石打石原理,磨损小。
(2)破碎率高、节能。
(3)具有细碎、粗磨功能。
(4)受物料水分含量影响小、含水份可达8%左右。
(5)更工作噪声低于75分贝(db级),粉尘污染少。
(6)适合破碎中硬、特硬物料。
(7)产品成立方体,堆积密度大,铁污染极小。
(8)叶轮自衬磨损小、维修方便。
 
GPR立式冲击式破碎机结构
GPR立式冲击式破碎机主要由进料斗、分料器、涡动破碎腔、叶轮体、主轴总成、底座、传动装置及电机等七部分组成。
1.进料斗
进料斗的结构为一倒立的棱台体(或圆筒体),进料口设置耐磨环,从给料设备的来料经给料斗进入破碎机。
 
2.分料器
分料器安装在涡动破碎腔的上部,分料器的作用就是将从给料斗来料进行分流,使一部分物料经由中心入料管直接进入叶轮被逐渐加速到较高速度抛射出去,使另一部分物料从中心入料管的外侧,旁路进入涡动破碎腔内叶轮的外侧,被从叶轮抛射出来的高速度物料冲击破碎,不增加功率消耗,增大生产能力,提高破碎效率。
 
3.涡动破碎腔
涡动破碎腔的结构形状为上、下两段圆柱体组成的环形空间,叶轮在涡动破碎腔内高速旋转,涡动破碎腔内也能驻留物料,形成物料衬层,物料的破碎过程发生在涡动破碎腔内,由物料衬层将破碎作用涡动破碎腔壁隔开,使破碎作用仅限于物料之间,起到耐磨自衬的作用。观察孔是观察叶轮流道发射口处耐磨块的磨损情况及涡动破碎腔顶部衬板的磨损情况,破碎机工作时必须将观察孔密封关严。分料器固定在涡动破碎腔的上部圆柱段。叶轮高速旋转产生气流,在涡动破碎腔内通过分料器、叶轮形成内部自循环系统。
 
4.叶轮
叶轮结构由特殊材料制作的空心圆柱体,安装在主轴总成上端轴头上,用圆锥套和键联接传递钮距,高速旋转,叶轮是pl立式冲击破碎机的关键元件。物料由叶轮上部分料器的中心入料管进入叶轮的中心。由叶轮中心的布料锥体将物料均匀的分配到叶轮的各个发射流道,在发射流道出口,安装有特殊材料制成的耐磨块,可以更换。叶轮将物料加速到60-75m/s速度抛射出去,冲击到涡动破碎腔内的物料衬层,进行强烈的自粉碎,在锥帽和耐磨块之间装有上、下流道板,保护叶轮不受磨损。
 
5.主轴总成
主轴总成安装在底座上,用以传递电动机经由三角皮带传来的动力及支撑叶轮旋转运动。主轴总成由轴承座、主轴、轴承等组成。
 
6.底座
涡动破碎腔、主轴总成、电动机、传动装置均安装在底座上,底座结构形状,中部为四棱柱空间,四棱柱空间的中心,用于安装主轴总成,两侧形成排料通道。双电动机安装在底座纵向两端,底座可安装在支架上,也可直接安装在基础上。
 
7.传动装置
采用单电机或双电机驱动的皮带传动机构(75KW以上,为双电机传动),双电机驱动两台电动机分别安装在主轴总成两侧,两电机皮带轮用皮带与主轴皮带轮相连,使主轴两侧受力平衡,不产生附加力矩。
 
GPR立式冲击式破碎机工作原理
物料由机器上部垂直落入高速旋转的叶轮内,在高速离心力的作用下,与另一部分以伞状形式分流在叶轮四周的物料产生高速撞击与粉碎,物料在互相撞击后,又会在叶轮和机壳之间以物料形成涡流多次的互相撞击、摩擦而粉碎,从下部直通排出,形成闭路多次循环,由筛分设备控制达到所要求的成品粒度。
 
GPR立式冲击式破碎机维护与保养
⒈定期停机打开观察门观察冲击式制砂机内部磨损情况,中心入料管、锥帽、叶轮上、下流道衬板、圆周护板、耐磨块的磨损程度,磨损后应及时更换或修补,更换耐磨块时应同时更换,保证耐磨块重量相同。严禁破碎机工作过程中打开观察门观察内部工作情况,以免发生危险。发现叶轮体磨损及时更换找制造厂家修补。特别注意,未经制造厂家同意,严禁私自自制叶轮。
⒉制砂机的传动三角胶带拉紧力大小应调整适当,以保证三角胶带受力均匀,双电机驱动时,两侧三角胶带应进行分组选配使其每组长度尽可能一致,方能保证制砂机设备节能高效;
⒊制砂机在工作到400小时的时候应适量的加入润滑脂,到工作到2000小时的时候就要打开主轴总成对承进行清洗了,如果工作到7200小时的时后就必须更换新的轴承了。
⒋制砂机的润滑为干油润滑方式,加入量为轴承空腔的二分之一到三分之二,每工作一班时,添加适量润滑脂。
⒌在工作过程中,因制砂机属于高速运转的设备,应该特别的注意安全。工作人员应远离设备,若需上机修理的话,必须断电后方可进行操作。
 

 

GPR Sand Maker

Due to the increasing market demand for the scale, intensification, energy conservation, environment protection and high-quality machine-made sand, HENGJI, a Chinese professional sand maker manufacturer, further optimizes the structure and function of traditional vertical-shaft impact crushers and launches a new generation of sand-making and reshaping machine with high efficiency and low costs --- GPR Vertical-shaft Sand Maker.

Product Features: Lower maintenance costs, longer service life of vulnerable parts, bigger capacity

Input Size: 0-50mm
Capacity: 100-580T/H
Material: Granite, quartz, basalt, pebble, limestone, dolomite, etc.

Working Principle

GPR Vertical-shaft Impact Crusher (also known as “Sand Maker”) has two feed modes – “feed at center” and “feed at center & sides”. As for the former mode “feed at center”, materials at the feed hopper firstly pass through the central hole into the high-speed spinning rotor. In the rotor, materials are fully accelerated and thrown outwards from the launching port to collide with a part of materials that freely fall after rebound. Next, materials hit the surrounding vortex material liner (or the impact block) inside the vortex chamber together. In the chamber, materials are bounced to the top of crushing chamber firstly and then change their direction by moving downwards to form a material curtain with materials emitted from the runner of impeller. Finally, finished products are discharged from the bottom discharge opening. As for the latter mode “feed at center & sides”, firstly, materials at the feed hopper pass through the circular hole. Then, materials are divided into two parts by the distributing tray. One part of materials enter the high-speed rotating impeller while the other part of materials fall from all sides of the tray. Materials in the impeller would be accelerated rapidly and thrown outwards at a high speed to collide with materials falling from all sides of the tray. Next, all materials hit the surrounding vortex material liner (or the impact block) inside the vortex chamber together. In the chamber, materials are bounced to the top of crushing chamber firstly and then change their direction by moving downwards to form a material curtain with materials emitted from the runner of impeller. Finally, finished products are discharged from the bottom discharge opening.
 

Product Parameters

型号Model 制砂
Sanding making
整形
Reshaping
制砂
Sanding making
整形
Reshaping
主轴转速(r/min)
Spindle speed(r/min)
功率(kw)
Power (kw)
产品粒度D50(mm)
软、硬、极硬
Product size D50 (mm)
Soft, hard, extremely hard
最大进料粒度(mm)
Maximum feeding size (mm)
通过量(t/h)
Throughput (t/h)
GPR7000 45 45 80-280 80-280 1200-1800 132×2 6.0 8.2 11.0
GPR8000 45 45 188-380 188-380 1200-1800 160×2 6.5 8.4 11.5
GPR8500 45 45 230-400 230-400 1200-1800 200×2 6.5 8.4 11.5
GPR9000 45 45 275-450 275-450 1200-1500 250×2 7.5 9.5 12
GPR9500 45 45 290-500 290-500 1300-1700 280×2 7.5 9.5 12

Note:

1.The bulk specific weight is calculated by 1.6t/m³. When the width of the feeding port is above 600mm, it is a large-scale machine while when the width ranges from 300 to 600mm, it is a medium-sized machine.

2.Product pictures and parameters about models, data, performances and specifications on this website are for reference only. There is a chance that HENGJI may make changes on above-mentioned information. For specific messages, please refer to the real objects and user manuals. Without special instructions, HENGJI keeps the right to explain all data involved in this website.

 


联系我们
Contact
联系我们
我们很想听到您的声音

400电话:4001360076

手机号码:18908682420

客服QQ:

Email:hbhjkj@ezhjzg.com

地址:湖北省鄂州经济开发区杜山工业园循环路西侧500米

[向上] 
在线客服

在线咨询

在线咨询

在线咨询

咨询电话:
4001360076
二维码

官方微信扫一扫